14 replies to this topic

[TheEnglishGuy]

GoApeOnline Store

Get them while they're still in stock!

English

[sbrooker]

TheEnglishGuy, on 21 June 2011 - 09:26 PM, said:

GoApeOnline Store

Get them while they're still in stock!

English

Whoa!! Thanks for the heads up.  Just purchased one.

[SplatU]

Is it a switched trigger or still hall-effect?

[TheEnglishGuy]

It'll be Hall Effect .. there's no way without changing the trigger itself they'd be able to get that working.

English

[ZANIAC]

So, no more safety shots? I should tell me buddy about this ASAP!

[Midnight]

About time!!! Too bad the TM-7 is now long gone...

[Sickest_tm7]

Oh man! Just bought mine! There was only 5 left in stock when I purchased it. Good luck everyone!

[Talyn]

just FYI under Tm-15 mods I posted a new topic with some things to be careful of when installing the board, also English put up and install video.

[ephil]

Posted to APE as well.

I just installed the TM7 Rampage board and it acts like it is not seeing the trigger...

I have the FLASC single trigger and have installed your magnet.

When I turn on the board, it beeps and the LED flashes a rapid teal ~3-4 times. At this point the LED is not lit up. I can then move the firing mode switch to any of the pre-programmed settings and the LED will respond correctly with the setting it is in.

With air in the marker and a paintball in the breach, I get nothing when pulling the trigger. I turn the eyes off by holding the power button in for one second and the LED does a slow pulse purple. Pull the trigger and no response.

I tried the one second hold of the trigger to do a "Forced Shot" and still nothing...

Any suggestions?

[Posting this here as I will need to get my stock board in tomorrow night if I can't find a resolution to this and I was hoping to play with the new board this Sat ]

[TheEnglishGuy]

Sounds like the power button and selector are working correctly, so either a) you didn't reconnect the solenoid correctly or b) you need to adjust the trigger screw/magnet further down inside the trigger.  Did you leave the magnet level with the top of the trigger?

English

[ephil]

TheEnglishGuy, on 07 July 2011 - 10:42 PM, said:

Sounds like the power button and selector are working correctly, so either a) you didn't reconnect the solenoid correctly or b) you need to adjust the trigger screw/magnet further down inside the trigger.  Did you leave the magnet level with the top of the trigger?

English

I was able to get it to give a response on trigger pull. I needed to set the #4 travel screw flush with the trigger so I could pull the trigger "more"... The activation screw is down in as far as it can go [twisted an allen wrench trying to get it down more].

So, right now it looks like I am good to use the new board tomorrow. I do kinda wish I had a little play with the activation screw though...

[side-effects]

ephil, on 08 July 2011 - 11:04 AM, said:

I was able to get it to give a response on trigger pull. I needed to set the #4 travel screw flush with the trigger so I could pull the trigger "more"... The activation screw is down in as far as it can go [twisted an allen wrench trying to get it down more].

So, right now it looks like I am good to use the new board tomorrow. I do kinda wish I had a little play with the activation screw though...

Check your thread over on PBN. I posted a response there.

[ephil]

side-effects, on 08 July 2011 - 11:28 AM, said:

Check your thread over on PBN. I posted a response there.

Heh yeah, I saw that reply first and then came here to update what I had to do so the information was spread out to where all I posted. Thanks for the reply bud

[side-effects]

ephil, on 08 July 2011 - 12:07 PM, said:

Heh yeah, I saw that reply first and then came here to update what I had to do so the information was spread out to where all I posted. Thanks for the reply bud

No problem, glad I could help!

[camry90]

no more in stock?